Reset on Nico Maas

[1841] Reset Password / Config, ROMMON Upgrade and Software Upgrade on Cisco 1841

Sun, 08 Feb 2015 15:35:45 +0000

1.) Reset Password / Config

Connect to the router via Serial Cable
Power on the router, but send a break during the first 60 seconds of boot time to get to the rommon CLI
enter confreg 0x2142 followed by a reset
Router is booting up, as soon as it does enter the system configuration dialog, answer the question with no
enable
conf t
config-register 0x2102
exit
wr mem (because I just want to overwrite the old config :)!)

2.) ROMMON Upgrade

[Win7+] Reset IP Stack

Sat, 26 Apr 2014 15:13:16 +0000

If your network doesn’t do networking anymore - and it comes down to the Windows IP Stack, try reseting it this way:
(In Admin CMD):

netsh int ip reset C:\netsh.log.txt
netsh winsock reset

After that, reboot

HTC Universal

Fri, 01 Apr 2011 09:00:53 +0000

I found a “bricked” HTC Universal without - everything.
So I decided to piece it back together.
First thing to find was an USB Cable to recharge the battery.
Working is an normal Mini USB Cable, even tough the connector looks different.

After that, I found out that the HTC was a brick.
So to unbrick:

get mtty1.42.exe, enter bootloader mode , (Power + Light Bulb + Reset)

Stop Activesync USB connection
Uni : Reboot Bootloader then Connect USB
PC : Run mtty1.42.exe
Choose USB in “Port” (Reconnect if can’t find/reconglize USB and try remove sim and sd card)
type : task 28 55aa
Press Enter
Cause DOC reformatted, so there’s no rom in DOC ,try reflash any rom that you like .

For task 28 55aa in mtty success , will show the message (attachment )

[79XX] Cisco IP Phone Factory Reset & Reboot

Wed, 08 Sep 2010 06:26:44 +0000

To Factory Reset a Cisco IP Phone do the following:

Press and hold #, disconnect and reconnect Power
The Phone will check through the Line LEDs, on an 7911 or similar it will just light up the both Menu Keys and the Reciever \ Handset LED - after that, let go of #
Enter following: 1 2 3 4 5 6 7 8 9 * 0 #
The Phone should start up and grab the latest config from your Callmanager

To just Reboot a Cisco IP Phone do following:

Snom 360 Update and Password Reset

Fri, 29 Jan 2010 08:24:39 +0000

WARNING, this is ONLY for Users on an Snom 360 with Firmware Revision 6.X.
If you got an different Revision the steps could be different.
Check out the Snom Wiki in that case ( http://wiki.snom.com/Firmware ).
Basically we just do reflash the Firmware with the same Revision again to erase data and passwords and unlock the Phone.
Than we do an automatic update to the latest release.

Download the latest Snom 360 Firmware from the Snom Website for your Revision ( http://wiki.snom.com/Firmware/V6/Latest_Release )
Download tftpd32 or an similar tftp Server
Rename the Firmware to snom360.bin and upload it to the root Directory of the tftp Server
Plug in the Network Port and Power to the Snom
As the message “To Update by TFTP: Press Any Key” appears, press any key on the phone
Enter valid IP Data for the Phone. Always press Next. I.e. the IP, the Subnet, the Gateway, DNS and the IP of your tfp Server.
As you’re finished, it will ask for this again and again, press Check Mark right beside the big X Button. The tfp Download will start. Don’t unplug the phone during the Firmware Update. The Phone will automatically reboot after the flash is done.
After this flash we have reset all data - including the passwords, so we now can press the Help Button on the phone and get the ip adress of the phone, connect to it by using an HTML Browser. But before you access the website, you need to enter the Administrative mode of the phone, otherwise you won’t be able to set any setting or update the phone. So press the Settings Button and press “Administrative Mode” - password is 0000 on default. Press Check Mark to accept. Now access the Website.
To update to version 7 Firmware (the latest Firmware, experimental) you need to go to the Advanced Tab, scroll down to Update. Set the Update Policy to “Update automatically” and the Setting URL to “http://provisioning.snom.com/update6to7/update_once.php". Press Save and Reboot, Accept with Yes. The Phone will Reboot.
After the reboot, the phone will access the internet and check automatically for an update, download it and start flashing. It will reboot serval times, don’t power it off until its done. It should take something like 10 Minutes or more, depending on your Internet connection. If it doesn’t reboot anymore and does show the normal menu for longer than half an minute you can consider it ok.
You can now create Identitys (Profiles) for your Sip / VoIP Accounts and reregister them via the Webinterface.

Astaro Security Gateway v7 Factory Reset

Fri, 17 Jul 2009 22:42:15 +0000

Access to SSH or console with root passwords:

/etc/init.d/factoryreset reset

No Access to SSH or root passwords are lost:

Connect a keyboard and monitor to the system.
Wait for boot prompt
Enter:

boot: default factoryreset

After that you can go to your during the installation definied IP like: https://192.168.0.1

Alternativ:

Boot on the ASG from a Knoppix CD
Login as root
Mount the root partition of the ASG with: mount –t ext3 /dev/sda7 /mnt
Go to the config on the ASG: cd /mnt/etc/wfe/conf/; vim setting
Change reset_pwd = 0 to reset_pwd = 1
Save
Run cd /; umount /mnt; reboot
Access the install IP

3Com Switches 1100, 3300 Factory Reset

Thu, 16 Jul 2009 13:17:03 +0000

COM port, 9600/8/N/1/N
Web Or telnet to that address, hit [enter] once or twice to get the login prompt.
Default logins to try are admin/(no password) or security/security. One of those 2 should bring up the management menu.
reset factory defaults, type SYSTEM[enter] then type INITIALIZE[enter].