{"id":405,"date":"2010-02-17T14:58:56","date_gmt":"2010-02-17T12:58:56","guid":{"rendered":"http:\/\/nico-maas.de\/wordpress\/?p=405"},"modified":"2011-03-10T09:35:22","modified_gmt":"2011-03-10T08:35:22","slug":"jasager-fonfon-newbie-guide-to-installlation-of-jasager-1-0-firmware","status":"publish","type":"post","link":"https:\/\/www.nico-maas.de\/?p=405","title":{"rendered":"[Jasager] Fon\/Fon+ Newbie Guide to Installlation of Jasager 1.0 Firmware"},"content":{"rendered":"

Pre Info:
\nThis guide has been made with an Fon+ (2201), but should work with any other
\nFonera Classic as well. Only limitation is that I have Problems with my
\nJasager in Terms of SSIDs, there seems to be a Problem which hasn't been
\naddressed by Digininja, but the Rest should work.
\n(Problem described here: http:\/\/hak5.org\/forums\/index.php?showtopic=13883 )<\/p>\n

This guide should be quite useful and has been written by using guides and
\nstuff from this Forum, I just wrote it together and added my own experiances.
\nMaybe that will turn out as a good starting point and help some newbies.<\/p>\n

This Guide ain't perfect and if you think I could add some info - just write me,
\nI would be happy to provide more accurate Information to make life for new Jasager Friends easier!<\/p>\n

Good Luck,
\nYours, Nico<\/p>\n

\n

\"\"<\/a><\/p>\n

\n

0.) Get it started!
\n- Get the Jasager 1.0 Firmware from Digininja
\nhttp:\/\/www.digininja.org\/jasager\/download.php
\n- Built an Serial Adapter
\nIts not that hard and you should built one - so you can recover an dead Fonera.
\nI.e. http:\/\/www.dd-wrt.com\/wiki\/index.php\/LaFonera_Hardware_Serial-Cable-Port
\nI built that myself (\"the ugly one\") and it works.
\nJust to add two things:
\ni) You need to wire RS232 TX to the RX of the Serial (S2) and RS232 RX to the TX
\n(S3) of the Serial Connector (and 5 is the Ground)
\nii) If you use an Fon+ (2201), the Serial Connector on the Phone is like that:<\/p>\n

ethernet port<\/p>\n

c x VCC 3,3 V MEMORY
\na x TX
\ns x RX CPU
\ne x GND<\/p>\n

1.) Flashing the Fon+ to Jasager
\na) With Serial Port only:
\n- Extract the two Firmware Files onto your PC
\n- Connect to Serial (9600 baud, 8 Bit Data, 1 Stop Bit, No Software\/Hardware Flow Control)
\n- Power Up the Fonera and Press CTRL+C (within 2 Seconds)
\nYou end up in RedBoot><\/p>\n

Enter fconfig and press Enter until you come to the point Console Baud Rate.
\nChange the 9600 to 115200. Press enter again till the end and accept the flash with y.
\nEnter Reset and change the Serial Port settings to 115200 baud.
\nRepower the Fonera and Press CTRL+C (within 2 Seconds)
\nYou end up in RedBoot><\/p>\n

Enter these Commands:
\n\/\/ Complete Kill of the Fonera Software:
\nfis init -f
\n\/\/ Download the Firmware Header and Root (fis can take about 20 Minutes!)
\nload -r -b %{FREEMEMLO} openwrt-atheros-vmlinux.lzma -m xmodem
\nfis create -e 0x80041000 -r 0x80041000 vmlinux.bin.17
\nload -r -b %{FREEMEMLO} openwrt-atheros-root.squashfs -m xmodem
\nfis create -l 0x6F0000 rootfs
\n\/\/ Configure Bootup, enter:
\nfconfig
\n\/\/ Enter Bootup Script, enter these two lines and press Enter a third time
\nfis load -l vmlinux.bin.17
\nexec<\/p>\n

\/\/ The complete Config should look like that (nothing else changed as the Bootup Script!)
\nRedBoot> fconfig
\nRun script at boot: true
\nBoot script:
\nEnter script, terminate with empty line
\n>> fis load -l vmlinux.bin.17
\n>> exec
\n>>
\nBoot script timeout (1000ms resolution): 2
\nUse BOOTP for network configuration: false
\nGateway IP address:
\nLocal IP address: 192.168.1.1
\nLocal IP address mask: 255.255.255.0
\nDefault server IP address: 192.168.1.254
\nConsole baud rate: 9600
\nGDB connection port: 9000
\nForce console for special debug messages: false
\nNetwork debug at boot time: false
\nUpdate RedBoot non-volatile configuration - continue (y\/n)? y
\n... Erase from 0xa87e0000-0xa87f0000: .
\n... Program from 0x80ff0000-0x81000000 at 0xa87e0000: .
\nRedBoot>
\n\/\/ Reboot, you're done with flashing!
\nreset<\/p>\n

b) With Serial Port and Tftp Server:
\n- Extract the two Firmware Files onto an reachable tftp Server
\n- Connect the Wan Port to your Network
\n- Connect to Serial (9600 baud, 8 Bit Data, 1 Stop Bit, No Software\/Hardware Flow Control)
\n- Power Up the Fonera and Press CTRL+C (within 2 Seconds)
\nYou end up in RedBoot><\/p>\n

Enter these Commands:
\n\/\/ First IP is the Fonera IP\/Subnet, Second is the TFTPServer
\nip_address -l 192.168.2.99\/24 -h 192.168.2.8
\n\/\/ Complete Kill of the Fonera Software:
\nfis init -f
\n\/\/ Download the Firmware Header and Root (fis can take about 20 Minutes!)
\nload -r -b %{FREEMEMLO} openwrt-atheros-vmlinux.lzma
\nfis create -e 0x80041000 -r 0x80041000 vmlinux.bin.17
\nload -r -b %{FREEMEMLO} openwrt-atheros-root.squashfs
\nfis create -l 0x6F0000 rootfs
\n\/\/ Configure Bootup, enter:
\nfconfig
\n\/\/ Enter Bootup Script, enter these two lines and press Enter a third time
\nfis load -l vmlinux.bin.17
\nexec<\/p>\n

\/\/ The complete Config should look like that (nothing else changed as the Bootup Script!)
\nRedBoot> fconfig
\nRun script at boot: true
\nBoot script:
\nEnter script, terminate with empty line
\n>> fis load -l vmlinux.bin.17
\n>> exec
\n>>
\nBoot script timeout (1000ms resolution): 2
\nUse BOOTP for network configuration: false
\nGateway IP address:
\nLocal IP address: 192.168.1.1
\nLocal IP address mask: 255.255.255.0
\nDefault server IP address: 192.168.1.254
\nConsole baud rate: 9600
\nGDB connection port: 9000
\nForce console for special debug messages: false
\nNetwork debug at boot time: false
\nUpdate RedBoot non-volatile configuration - continue (y\/n)? y
\n... Erase from 0xa87e0000-0xa87f0000: .
\n... Program from 0x80ff0000-0x81000000 at 0xa87e0000: .
\nRedBoot>
\n\/\/ Reboot, you're done with flashing!
\nreset<\/p>\n

c) Via Fon Flash:
\n- Get FonFlash (and install wpcap Drivers as well, are included in Wireshark)
\n- Start FonFlash
\n- Select your Network Interface Card
\n- Select Rootfs (openwrt-atheros-root.squashfs)
\n- Select Kernel (openwrt-atheros-vmlinux.lzma)
\n- Press Flash Router now and Power Up the Fonera.
\n- Takes approx. 20 Minutes<\/p>\n

2.) Connect and Basic Settings
\n\/\/ telnet to 192.168.1.1 and change the root passwd to enable SSH.
\ntelnet 192.168.1.1
\npasswd
\nilovepineapples
\nilovepineapples<\/p>\n

3.) Fixing Webif
\nYou got two Webinterfaces on the Jasager.
\nFirst the Karma\/Jasager one at 192.168.1.1:1471,
\nand Second the Webif\/X-Wrt on 192.168.1.1.
\nIn Webif, you can change things like IP Adresses and watch a bunch of data.
\nEasy configuration for your Fon+ if you're not so used to the CLI in Linux.
\nNow that you have changed the root password and therefor have access to ssh,
\nyou can use putty to connect to 192.168.1.1<\/p>\n

a) Opkg
\necho \"src X-Wrt http:\/\/downloads.x-wrt.org\/xwrt\/kamikaze\/8.09\/atheros\/packages\" >> \/etc\/opkg.conf
\nopkg update
\nopkg remove -recursive luci-*
\nopkg update
\nopkg install webif
\nreboot<\/p>\n

Manual
\n\/\/ Remove Previous Install
\nopkg -recursive remove haserl
\n\/\/ Download and move these files to the tmp directory on the fon using winSCP
\nhaserl_0.9.24-1_mips.ipk
\nwebif_0.3-4709_mips.ipk
\nwebif-theme-xwrt_0.3-4709_all.ipk
\n\/\/ Install the files using putty.
\nopkg install haserl_0.9.24-1_mips.ipk
\nopkg install webif_0.3-4709_mips.ipk
\nopkg install webif-theme-xwrt_0.3-4709_all.ipk<\/p>\n

4.) Enable Wireless
\nuci set wireless.wifi0.disabled=0
\nuci commit wireless && wifi
\nreboot<\/p>\n

5.) Duplicate Ports (only on Fon+ 2201)
\nhttp:\/\/www.frontiernet.net\/~beakmyn\/JasagerIntercept_Install.html<\/p>\n

6.) There is no Step 6. Have fun!<\/p>\n

(( http:\/\/hak5.org\/forums\/index.php?showtopic=14973 More Info on Jasager on http:\/\/www.digininja.org\/jasager\/ ))<\/p>\n